팔레타이징 로봇을 4가지 숫자로 지정하는 방법
팔레트 크기, 케이스 중량, 스택 높이 및 분당 케이스가 암을 결정합니다. 그 밖의 모든 것(그리퍼, 안전, 소프트웨어)은 이 네 가지를 따릅니다.
Start with the pallet, not the robot
A palletizing arm has to reach the far corner of the tallest stack, not the middle of a conveyor. Measure the pallet footprint (1200×1000 and 1200×800 mm cover most of Europe; 1219×1016 mm is the US GMA size), the load height including the pallet itself, and the height of the infeed conveyor. The arm's working envelope must cover the worst-case corner at full stack height — that corner is what sets the reach, not the near side.
Payload is the case plus the gripper
Take the heaviest case, add the gripper (a vacuum tool for cartons is usually 15–40 kg, a mechanical clamp for bags more), add 15–20 % for acceleration and off-centre loads. Our four-axis palletizing line covers 30 kg to 800 kg: the TR1030B-185 handles 30 kg at 1,850 mm, the TR10165B-310 covers 165 kg at 3,100 mm, and the TR10800B-300 goes to 800 kg. A mid-size case line usually lands on the 165 kg class once the gripper and margin are counted — buyers regularly under-specify this by one size.
Cycle time decides the axis count
Four-axis arms are faster and cheaper for floor-level palletizing because they do not need to reorient the wrist. If the pattern needs the case rotated on every pick — mixed SKU pallets, labels facing out — a six-axis arm or a servo gripper that rotates is the better answer. Ask for the pattern software with the quote: a line that needs an engineer to reprogram every SKU change is not the same purchase as one where the operator picks a pattern from a screen.
우리에게 보낼 것
A photo of the pallet as it is stacked today, the case weight and dimensions, cases per minute, the infeed height, and the plant's voltage. With those five we return a cell layout, the arm model, the gripper concept and a lead time. Standard palletizing arms ship in 15–40 days depending on payload class.
Questions we get asked
케이스 무게가 20kg인 경우 어떤 페이로드를 선택해야 합니까?
그리퍼와 15~20% 마진 계산: 케이스 20kg과 진공 도구 25kg이 50~60kg 등급에 가까워지므로 일반적으로 30kg 암은 너무 작고 165kg 암은 편안합니다.
하나의 로봇이 두 개의 생산 라인을 팔레타이징할 수 있습니까?
예, 라인이 도달 범위 내에 있고 사이클 시간이 이동을 허용하는 경우입니다. 하나의 셀에 두 개의 투입 컨베이어가 있는 것이 일반적입니다. 제약 조건은 둘 중 하나도 굶지 않고 두 라인을 모두 대기열에 넣는 패턴 소프트웨어입니다.
울타리가 필요한가요?
속도가 빠른 4축 팔레타이징 암은 일반적으로 조명 울타리나 안전 스캐너 뒤에서 작동합니다. Cobot 기반 팔레타이징이 존재하지만 중량 범위의 하한으로 제한됩니다.
Machines this applies to
- 30kg 고속 팔레타이징 로봇TR1030B-185 · 15일
- 165kg 팔레타이징 로봇, 도달 거리 3,000mmTR10165B-310 · 20일
- 800kg 헤비듀티 팔레타이징 로봇TR10800B-300 · 40일
Keep reading
- 기계와 함께 배송되는 문서(및 서명하기 전에 요청해야 할 사항)매뉴얼, 도면, I/O 목록, 예비 부품 목록, FAT 보고서, 포장 목록. 이 중 하나가 누락되면 커미셔닝을 위해 한 달 동안 이메일을 보내게 됩니다.
- 유리 외관 청소 로봇: 건물이 실제로 제공해야 하는 것로봇은 결정의 작은 부분입니다. 앵커, 물, 지붕 접근, 바람 제한 및 청소 직원과의 계약에 따라 사용 여부가 결정됩니다.
- 외골격 선택: 수동형 또는 전동식, 실제로 아픈 신체 부위수동 유닛은 자세에서 에너지를 빌려옵니다. 동력 장치는 토크를 추가합니다. 올바른 선택은 작업 기간, 부하, 작업자가 걷거나 서 있는지 여부에 따라 달라집니다.